CNC Manual Control Handle Remote For 3 Axis TB6560 Stepper Motor Driver Board (UC132)

The picture below is the interfaces diagram of the manual controller.You can refer to it to get more information of the interfaces as you will have to set up with them in the near future.
manual controller一》15P connector at both ends of the corresponding Definitions of the manual controller

1 2 3 4 5 6 7 8 9 10
Black Palm Red Orange Yellow Green Blue Purple Gray White

 

11 12 13 14 15
Powder Light green Black/White Palm/White Red/White

 

二》Handle the output interface definition

1 2 3 4 5 6 7 8
5V/VDD GND Estop Empower1 Empower2 Spindle X/Dir X/Step

 

9 10 11 12 13 14
Y/Dir Y/Step Z/Dir Z/Step C/Dir C/Step

 

二》HY-TB3DV-M axis drive board manual interface definition

Black Palm Red Orange Yellow Green Blue Purple
P1 P2 P3 P4 P5 P6 P7 P8
X/Step X/Empower Spindle X/Dir Y/Empower Z/Dir Z/Step Z/Empower
Gray White Powder Light green Black/White Palm/White Red/White
P9 P10 P11 P12 P13 P14 P15
5V/VDD GND Estop Y/Step Y/Dir Z/Limit Y/Limit

 

三》HY-TB4DV-M four-axis drive board manual interface definition

 

Black Palm Red Orange Yellow Green Blue Purple
P1 P2 P3 P4 P5 P6 P7 P8
Z/CEmpower C/Step Z/Step X/Dir X/Empower Y/Empower Y/Dir Z/ Dir

 

Gray White Powder Light green Black/White Palm/White Red/White
P9 P10 P11 P12 P13 P14 P15
5V/VDD GND Estop X/Step Y/Step Spindle C/Dir

四》HY-TB5DV-M axis drive board manual interface definition with manual controls

Black Palm Red Orange Yellow Green Blue Purple
P1 P2 P3 P4 P5 P6 P7 P8
Empower C/Step Z/Step X/Step X/Dir Y/Dir Z/Dir C/Dir

 

Gray White Powder Light green Black/White Palm/White Red/White
P9 P10 P11 P12 P13 P14 P15
5V/VDD GND Estop Y/Step D/Step Spindle DDir

 

TA4 handle axis defined

Black Palm Red Orange Yellow Green Blue Purple
P1 P2 P3 P4 P5 P6 P7 P8
Spindle A/Dir B/Dir B/ Empower C/Step D/Dir C/Dir A/ Empower

 

Gray White Powder Light green Black/White Palm/White Red/White
P9 P10 P11 P12 P13 P14 P15
5V/VDD GND GND D/Step B/Step C/允许 A/Step

Interface board handles the definition of

Black Palm Red Orange Yellow Green Blue Purple
P1 P2 P3 P4 P5 P6 P7 P8
C/Dir C/ Step X/ Step X/Dir Y/Dir Z/Dir Spindle Expand

 

Gray White Powder Light green Black/White Palm/White Red/White
P9 P10 P11 P12 P13 P14 P15
5V/VDD GND Estop Y/ Step Z/ Step E1 E2

 

Instructions

1: The first drive with a corresponding docking connector board good driver board

2: turn on the power switch, power indicator light

3: Click the corresponding axis manual control buttons, the corresponding stepper motor shaft rotation axis while the corresponding indicator light, release the button to stop stepping motor

4: Manually adjust the speed dial number is about 300 degrees rotation within the (limited spaces on both sides of the fixed position), clockwise rotation acceleration, deceleration counterclockwise rotation,

Now you must have get the method to set up the manual controls.If you want to get more information,please download the manual: http://www.marcmart.com/ebay/u/UC132/Remotel Controller.pdf

This entry was posted in Remote Controller and tagged , . Bookmark the permalink.

Leave a Reply